View NCP100SNT1_459432.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NCP100 Sub 1.0 V Precision Adjustable Shunt Regulator
The NCP100 is a precision low voltage shunt regulator that is programmable over a voltage range of 0.9 V to 6.0 V. This device features a guaranteed reference accuracy of 1.7% at 25C and 2.6% over the entire temperature range of -40C to 85C. The NCP100 exhibits a sharp low current turn-on characteristic with a low dynamic impedance of 0.20 W over an operating current range of 100 mA to 20 mA. These characteristics make this device an ideal replacement for zener diodes in numerous application circuits that require a precise low voltage reference. When combined with an optocoupler, the NCP100 can be used as an error amplifier for controlling the feedback loop in isolated low output voltage (2.3 V) switching power supplies. This device is available in an economical space saving TSOP-5 package.
Features http://onsemi.com
5 1 TSOP-5 SN SUFFIX CASE 483
* * * * * * * * * *
Programmable Output Voltage Range of 0.9 V to 6.0 V Voltage Reference Tolerance of 1.7% Sharp Low Current Turn-ON Characteristic Low Dynamic Output Impedance of 0.2 W from 100 mA to 20 mA Wide Operating Current Range of 80 mA to 20 mA Space Saving TSOP-5 Package Reference for Single Cell Alkaline, NiCD and NiMH Applications Low Output Voltage (2.3 V) Switching Power Supply Error Amp Battery Powered Consumer Products Portable Test Equipment and Instrumentation
PIN CONNECTIONS AND MARKING DIAGRAM
NC Anode Cathode 1 RAByyww 4 (Top View) YY = Year WW = Work Week Reference 2 3 5 Anode
Applications
ORDERING INFORMATION
Device Package TSOP-5 Shipping 3000 Units / 7 Reel
Cathode (K) NCP100SNT1 Cathode (K) Reference (R) 0.7 V Anode (A) Anode (A)
Reference (R)
Figure 1. Symbol
Figure 2. Representative Block Diagram
(c) Semiconductor Components Industries, LLC, 2002
1
March, 2002 - Rev. 5
Publication Order Number: NCP100/D
NCP100
MAXIMUM RATINGS (TA = 25C, unless otherwise noted.)
Rating Cathode to Anode Voltage (Note 1) Symbol VKA IK Value 7.0 Unit V
AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA
Cathode Current Range, Continuous (Note 2) -20 to 25 mA mA Reference Input Current Range, Continuous (Note 1) Thermal Resistance Junction to Air Iref -0.05 to 2.0 225 RJA TJ C/W C C Operating Junction Temperature Range Storage Temperature Range -40 to 125 -65 to 150 Tstg
RECOMMENDED OPERATING CONDITIONS
Condition Cathode to Anode Voltage Range Cathode Current Range Symbol VKA IK Min 0.9 0.1 Max 6.0 20 Unit V
AAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A A AAA A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AA
mA 1. This device series contains ESD protection and exceeds the following tests: Human Body Model 4000 V per JESD-22, Method A114B. Machine Model Method 400 V. 2. The maximum package power dissipation limit must not be exceeded. TJ(max) * TA PD + RqJA
ELECTRICAL CHARACTERISTICS (TA = 25C, unless otherwise noted.)
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAA AAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAA A A A A AAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A A A A AAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
Reference Voltage (IKA = 10 mA, Figure 3) VKA = 0.9 V TA = 25C TA = 0C to 70C TA = -40C to 85C VKA = 1.0 V TA = 25C TA = 0C to 70C TA = -40C to 85C Vref V 0.684 0.682 0.678 0.686 0.684 0.680 - 0.696 - - 0.698 - - 1.0 0.708 0.710 0.714 0.710 0.712 0.716 12 Reference Input Voltage Change Over Temperature VKA = 1.0 V, IK = 10 mA, TA = -40C to 85C, Figure 3 (Notes 3, 4) DVref mV mV Reference Input Voltage Change Over Programmed Cathode Voltage (IK = 10 mA, Figure 3) VKA = 0.9 V to 1.0 V VKA = 1.0 V to 6.0 V Regline -3.0 0 - 0.2 6.7 1.3 3.0 12 2.4 Ratio of Reference Input Voltage Change to Cathode Voltage Change VKA = 0.9 V to 6.0 V, IK = 10 mA, Figure 3 Reference Input Current (VKA = 1.0 V, IK = 10 mA) Minimum Cathode Current for Regulation DVref DVKA Iref mV/V nA mA mA W -100 - - - -30 80 70 100 - IK(min) IK(off) |ZKA| Cathode Off-State Current (VKA = 6.0 V, Vref = 0 V) 90 - Dynamic Output Impedance VKA = 1.0 V, IK = 100 mA to 20 mA, f v 1.0 kHz, Figure 3 0.2 3. Low duty cycle pulse techniques are used during testing to maintain the junction temperatures as close to ambient as possible. 4. The DVref parameter is defined as the difference between the maximum and minimum values obtained over the ambient temperature range of -40C to 85C. Vref (max) DVref = Vref (max) - Vref (min) DTA = T2 - T1 Vref (min) T1 T2 AMBIENT TEMPERATURE
Characteristic
Symbol
Min
Typ
Max
Unit
http://onsemi.com
2
NCP100
1.0 k Vin IK VKA Vin
1.0 k VKA IK
R1
+ CL
10 k
+
22 mF
100 k
Vref
R2
Vref
Figure 3. General Test Circuit
Figure 4. Test Circuit for Reference Input Voltage Change vs. Cathode Voltage
110 k IK VKA CL + + 22 mF 100 k 0.1 mF 0.01 mF Input +
1.0 k Output IK R1
50 k
R1
100 k
Figure 5. Test Circuit for Dynamic Impedance vs. Frequency
Figure 6. Test Circuit for Spectral Noise Density
REFERENCE INPUT VOLTAGE CHANGE (%)
1.0 VKA = 0.9 V
CATHODE VOLTAGE CHANGE (%)
IK = 250 mA f v 1.0 kHz CL = 22 mF Figure 3 VKA = 1.0 V
2.0
1.0
VKA = 0.9 V
IK = 250 mA f v 1.0 kHz CL = 22 mF Figure 3
0
0 VKA = 6.0 V
VKA = 1.0 V
VKA = 6.0 V
-1.0
VKA = 0.9 V
VKA = 6.0 V -2.0 -50 -25 0 25 50 75 100 125
-1.0 -50
-25
0
25
50
75
100
125
TA, TEMPERATURE (C)
TA, TEMPERATURE (C)
Figure 7. Reference Input Voltage Change vs. Ambient Temperature
Figure 8. Cathode Voltage Change vs. Ambient Temperature
http://onsemi.com
3
NCP100
20 IK, CATHODE CURRENT (mA) 15 10 5.0 0 -5.0 -10 -0.8 -0.6 -0.4 -0.2 IK, CATHODE CURRENT (mA) VKA= 1.0 V CL = 3.3 mF TA = 25C Figure 3 200 150 100 50 0 -50 VKA= 1.0 V CL = 3.3 mF TA = 25C Figure 3
IK(min)
0
0.2
0.4
0.6
0.8
1.0
1.2
-100 -0.6 -0.4
-0.2
0
0.2
0.4
0.6
0.8
1.0
1.2
VKA, CATHODE VOLTAGE (V)
VKA, CATHODE VOLTAGE (V)
Figure 9. Cathode Current vs. Cathode Voltage
Figure 10. Cathode Current vs. Cathode Voltage
DVref, REFERENCE INPUT VOLTAGE CHANGE (mV)
8.0 |ZKA|, DYNAMIC IMPEDANCE (W) VKA= 10 mA CL = 22 mF TA = 25C Figure 4
10 VKA= 1.0 V IK= 9.5 mA to 10.5 mA CL = 3.3 mF TA = 25C Figure 5
6.0
1.0
4.0
0.1
2.0
0 0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
0.01 1.0
10
100 FREQUENCY (Hz)
1.0k
10k
VKA, CATHODE VOLTAGE (V)
Figure 11. Reference Input Voltage Change vs. Cathode Voltage
Figure 12. Dynamic Impedance vs. Frequency
50 GAIN AV, VOLTAGE GAIN (dB) 30
120 EXCESS PHASE () Vref, REFERENCE VOLTAGE (mV)
706
60 PHASE
700
TA = -40C = 25C
10
0
694
-10
VKA= 1.0 V IK = 10 mA TA = 25C 100 1.0k 10k 100k
-60
688
= 70C = 85C = 105C
f 1.0 kHz CL = 3.3 mF Figure 3 200 250 300
-30 10
-120 1.0 M
682 50 100 150 IK, CATHODE CURRENT (mA)
FREQUENCY (Hz)
Figure 13. Small-Signal Voltage Gain and Phase vs. Frequency
Figure 14. Reference Voltage vs. Cathode Current for VKA = 0.9 V
http://onsemi.com
4
NCP100
698 Vref, REFERENCE VOLTAGE (mV) TA = -40C Vref, REFERENCE VOLTAGE (mV) 708 = 105C 704
697 = 25C = 70C = 85C = 105C f 1.0 kHz CL = 3.3 mF Figure 3 696 50 100 150 200 250 300
700 = 70C = 85C 696 = 25C TA = -40C f 1.0 kHz CL = 22 mF Figure 3 200 250 300
692 50
100
150
IK, CATHODE CURRENT (mA)
IK, CATHODE CURRENT (mA)
Figure 15. Reference Voltage vs. Cathode Current for VKA = 1.0 V
Figure 16. Reference Voltage vs. Cathode Current for VKA = 6.0 V
714 Vref, REFERENCE VOLTAGE (mV) 710 = 25C 706 702 698 694 690 0 TA = -40C f 1.0 kHz Figure 3 CL = 22 mF 4.0 6.0 = -40C = 85C = 70C = 105C
1000 NOISE VOLTAGE (nV/pHz) VKA = 1.0 V IK = 10 mA CL = 3.3 mF TA = 25C Figure 6
800
600
400
200
2.0
0 10
100
1.0 k FREQUENCY (Hz)
10 k
100 k
VKA, CATHODE VOLTAGE (V)
Figure 17. Reference Voltage vs. Cathode Current
Figure 18. Spectral Noise Density
6.0 VKA, CATHODE VOLTAGE (V) 5.0 4.0 3.0 2.0 1.0 NON-OPERATIONAL 0 1.0 10 CL, LOAD CAPACITANCE (mF) 100 0 200 400 600 800 1000 1200 1400 1600 t, TURN-ON TIME (s) STABLE OPERATION VIN (V) 0 2.0 0 VKA (V) UNSTABLE OPERATION IK = 0.08 mA to 30 mA CESR 4.0 W TA = -40C to 85C 1.0 IK = 10 mA CL = 3.3 F TA = 25C
0.5
Figure 19. Stability Boundary Conditions
Figure 20. Turn-On Time
http://onsemi.com
5
NCP100
APPLICATIONS INFORMATION The NCP100 is an adjustable shunt regulator similar to the industry standard 431-type regulators. Each device is laser trimmed at wafer probe to allow for tight reference accuracy and low reference voltage shift over the full operating temperature range of -40C to 85C (Figure 7). The nominal value for the reference is 0.698 V. This lower voltage allows the device to be used in low voltage applications where the traditional 1.25 V and 2.5 V references are not suitable.
Vin Rin VKA LOAD CL R2 Vref
the resistance and power value of Rin can be determined by the following equation.
Rin + Vin * VKA IK ) IL )
VKA R1)R2
The maximum current that will flow through Rin must be determined. This is the sum of the maximum values of cathode current, resistor divider network current, and load current. With Vin, set, the difference (Vin-VKA) is now constant. This value is divided by the maximum current calculated above to arrive at the value of Rin. Once the value of Rin is calculated, it's minimum power rating is easily derived by:
Pin + (Iin)2 Rin
R1
IK
Figure 21. Typical Application Circuit
The typical application circuit for this device is shown in Figure 21. The cathode voltage can be programmed between 0.9 V to 6.0 V to allow for proper operation by setting the R1/R2 resistor divider network values. The following equation can be used in calculating the cathode voltage (VKA). Note, if VKA is known then the ratio of R1 and R2 can be determined from this equation as well.
VKA + Vref 1 ) R1 ) Iref R1 R2
Once these values are determined, it should be verified that the minimum and maximum values of IK are within the recommended range of 0.1 mA to 20 mA under the worst case conditions. For stability, the NCP100 requires an output capacitor between the cathode and anode. Figure 19 shows the capacitance boundary values required for stable operation across the -40C to 85C temperature range. The goal is to remain to the right of the curve for any programmed cathode voltages. For example, if the VKA is programmed to 1.0 V, then a load capacitor value of 3.0 mF or greater would be selected. The load capacitor's equivalent series resistance, ESR, should be less than 4.0 W. Both the capacitance and ESR values should be checked across the anticipated application temperature range to insure that the values meet the requirements stated above.
Vin
The table below shows the required R1/R2 values using 1.0% resistors for commonly used voltages.
VKA (V) 0.9 1.0 1.8 3.3 5.0 6.0 R1 (kW) 30 R2 (kW) 100 100 100 100 100 100 R1
1.0 k
Iin
Vcomp
Rcomp VKA IK + CL
AAAAAA A A AAAAAAAAAAAAAAAAA A A AAAAAA A A AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA AAAAAA A AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAA
43.2 158 374 619 750
100 k
Vref
Because the error amplifier is a CMOS design the value of Iref is extremely low allowing it to be neglected for most applications. The low Iref also allows for higher R1 and R2 values keeping current consumption very low. The NCP100 is especially well suited for lower voltage applications, particularly at VKA = 1.0 V. As is seen in Figures 7 and 8, this device exhibits excellent cathode and reference voltage flatness across the -40C to 85C temperature range. In Figure 21, the input resistor (Rin) is nominally set to 1.0 kW. For proper operation, once Vin, R1 and R2 are set,
Figure 22. Negative Dynamic Impedance Circuit
One unique use for the NCP100 is that it can be configured for negative dynamic impedance as shown in Figure 22. This circuit is equivalent to Figure 21 with the addition of a small value resistor Rcomp in the cathode circuit. The regulated voltage output remains across the NCP100 cathode and anode leads. The voltage programming and stability requirements remain the same as in the typical application shown in Figure 21.
http://onsemi.com
6
NCP100
The circuit performs the same as the one in Figure 21 with the exception of the effects of Rcomp. As IK increases, the voltage across Rcomp also increases by:
Vcomp + IKA Rcomp
Vcomp effectively adjusts the NCP100 programmed VKA voltage slightly down since the R1/R2 voltage divider will try to hold the point it is connected to at the programmed voltage. The regulator VKA will now be lowered by the value of the Vcomp. This effect can compensate for the NCP100's intrinsic positive impedance versus cathode current (IK) to allow for 0 W or even a negative dynamic impedance. Figure 23 shows this phenomenon for a program voltage of 1.0 V. The NCP100 intrinsic positive dynamic impedance
20 IK, CATHODE CURRENT (mA) Rcomp= 3.1 W = 1.5 W = 0.15 W 15 Rcomp |ZKA| (W) (W) 0 0.2 0.15 0 1.5 -1.4 3.1 -1.6 IK = 0.1 mA to 20 mA TA = 25 C Figure 22 0 0.94 0.95 0.96 0.97 0.98 0.99 1.00 1.01 =0W
response is the Rcomp = 0 W curve. A 0 W dynamic impedance regulator response is realized with Rcomp = 0.15 W. Negative dynamic impedance responses are achieved with Rcomp u 0.15 W. Figure 24 shows the characteristic at a programmed VKA of 6.0 V. The 0 W dynamic impedance value corresponds to Rcomp = 2.9 W. Figure 25 shows the dynamic impedance versus cathode compensation resistance for programmed voltages of 1.0 V, 3.3 V and 6.0 V. It can be seen that any value up to the positive intrinsic dynamic impedance of the NCP100 can be realized. The other limit is that with a high enough negative dynamic impedance, the NCP100 V may drop below the minimum operating VKA voltage of 0.9 V, which can result in unpredictable performance.
20 IK, CATHODE CURRENT (mA) = 4.4 W 15 =0W 10 Rcomp= 5.8 W 5.0 IK = 0.1 to 20 mA TA = 25 C Figure 22 5.96 5.98 6.00 6.02 Rcomp |ZKA| W W 0 2.9 1.5 1.4 2.9 0 4.4 -1.6 5.8 -2.9 6.04 6.06 = 2.9 W = 1.5 W
10
5.0
0 5.94
VKA, CATHODE VOLTAGE (V)
VKA, CATHODE VOLTAGE (V)
Figure 23. Cathode Current vs. Cathode Voltage for Programmed VKA = 1.0 V
Figure 24. Cathode Current vs. Cathode Voltage for Programmed VKA = 6.0 V
3.0 |ZKA|, DYNAMIC IMPEDANCE (W) 2.0 = 6.0 V 1.0 0 -1.0 -2.0 -3.0 0 VKA= 1.0 V = 3.3 V IK = 1.0 mA to 20 mA f 1.0 kHz Figure 22 TA = 25 C
1.0
2.0
3.0
4.0
5.0
Rcomp, CATHODE COMPENSATION RESISTANCE (W)
Figure 25. Dynamic Impedance vs. Cathode Compensation Resistance
http://onsemi.com
7
NCP100
Rin R1
Vin
Vout
Vin R1
Vout
R2
R2 V out + 1 ) R1 V ref R2 ref
V out +
1 ) R1 V ref R2 be
V out min + 0.9 V ) V
V out min + V
Figure 26. High Current Shunt Regulator
Figure 27. Low Dropout Series Pass Regulator
AC Line Input
1/2 Opto
R1 Isolated DC Output
NCP 100 + UC3842
R2 -
1/2 Opto
Minimum Vout = (0.9 + 1.4) = 2.3 V
+ S
Q + +
R
Figure 28. Offline Converter with Isolated DC Output
The circuit in Figure 28 uses the NCP100 as a compensated amplifier for controlling the feedback loop of an isolated output line powered converter. This device allows the converter to directly regulate the output voltage at a significantly lower level than obtainable with the
common TL431 device family. The output voltage is programmed by the resistors R1 and R2. The minimum regulated DC output is limited to the sum of the lowest allowable cathode to anode voltage (0.9 V) and the forward drop of the optocoupler light emitting diode (1.4 V).
http://onsemi.com
8
+ +
NCP100 INFORMATION FOR USING THE TSOP-5 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to insure proper solder connection
0.094 2.4
interface between the board and the package. With the correct pad geometry, the packages will self align when subjected to a solder reflow process.
0.037 0.95 0.074 1.9 0.037 0.95 0.028 0.7 0.039 1.0 inches mm
TSOP-5
http://onsemi.com
9
NCP100
PACKAGE DIMENSIONS
TSOP-5 SN SUFFIX PLASTIC PACKAGE CASE 483-01 ISSUE B
D
5 1 2 4 3
S
B
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. DIM A B C D G H J K L M S MILLIMETERS MIN MAX 2.90 3.10 1.30 1.70 0.90 1.10 0.25 0.50 0.85 1.05 0.013 0.100 0.10 0.26 0.20 0.60 1.25 1.55 0_ 10 _ 2.50 3.00 INCHES MIN MAX 0.1142 0.1220 0.0512 0.0669 0.0354 0.0433 0.0098 0.0197 0.0335 0.0413 0.0005 0.0040 0.0040 0.0102 0.0079 0.0236 0.0493 0.0610 0_ 10 _ 0.0985 0.1181
L G A J C 0.05 (0.002) H K M
http://onsemi.com
10
NCP100
Notes
http://onsemi.com
11
NCP100
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative.
http://onsemi.com
12
NCP100/D

▲Up To Search▲

Price & Availability of NCP100SNT1

	To Download NCP100SNT1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .